VESSELBall Grip Screwdriver (for home use/Black) [No.220W-BC3C] (interchangeable) (Japan Import)

Nice bit driver & bit set. Very comfortable in the hand, the rubber grip keeps it from slipping and does a good job of helping transfer torque.

All in all, I would say if you need to work in tight areas or use the JIS #3 head pass on this.The multi tipped #1#3 side does not work the well. It works okay for #1 but #3 does not hold a grip if the screw is tight. The #3 bit kept slipping because the teeth didn't have enough of a grip on the inside of the screw so it started to strip the screw. Even if you push very hard it slips constantly and will always slips if you need to hold it at an angle. I had to get another #3 to unscrew everything that was tightly screwed in, it worked pretty well on moderately tightened screws, but I can't recommend it.The bulbous handle is nice enough to hold onto but it makes the screwdriver too wide for a lot of situations so you have to hold it sideways to screw things in. (And as mentioned above if you angle the #1#3 head even slightly it instantly slips).The magnetic bit holder is awesome and the bits stay in the screwdriver perfectly well.Again, if you need to work in tight areas or use the JIS #3 head pass on this however, if you’re not planning on using the #3 head or working in tight spots this is a great screwdriver.

Was using Phillips on both of my Suzukis until I discovered these and they are miles better, there is almost no chance of stripping a screw or bolt with these. Even on a stripped screw these will get the job done, just lightly tap the flat spot on the back with a hammer and it will come right out. I will NEVER use phillips screwdrivers again on these. (do note not all Japanese vehicles use JIS)

I had watched some great reviews on this Screwdriver set. As stated in the reviews the handle feels very comfortable in the hand. However the bits are very difficult to insert or remove into the handle or the bit holder. The instructions are in Japanese. One would think how hard is it to figure out how to use a Screwdriver? But it's the bit holder that needs the instructions. It has a clip and a magnet, and I couldn't figure out what the Clip was for. I assume the magnet is for holding on to screws. But the clip? No idea. Returning because of the difficulty inserting and removing bits from the handle.

I like the bulbous driver handle. Easy to hold.

Bought this because the triangle tip would fit several of my son's toys, it arrived and i was floored by the build quality and extremely ergonomic grip.

As a screwdriver nut (yep, I did that), this is a GREAT tool for the money. The JIS bits (complicated, so: TL;DR: they're back-compatible and probably better to use with Philips screws) are fantastic. Quality steel, good handle that feels good and works fast even without a clutch (kind of makes your hand the clutch - you'll appreciate how smart the ball-design is pretty quickly!).[AS FOR THE Wile E. Coyote SOOPER-GENIUS who couldn't figure out what the "clip" was for - it has the word "MAGNETIZER" printed on it (!). You take it from there. (Hint, out of pity: pretty sure you can also DE-magnetize with it, going the other direction. Take a few swipes, then test.) Sigh. To quote from Ferris Bueller: "I weep for the future."]

Very disappointed!!!...

今までよくある家庭用のドライバーセットを使用していましたが、こちらにして正解でした。まずグリップのおかげで力が圧倒的にはいりやすい。それから刀身？が長いため、狭いところもいける。さらに帯磁、脱磁も自由自在。よくあるセットほどじゃないけど、結構コンパクト。とりあえず家に一つ置いておいていいと思います。

本当は、電動ドライバーを買おうと思って間違って買ってしまったのですが、以前カラーBOXを組み立てた時、ドライバー🪛で、手のひらの皮が剥けてしまって痛い思いをしたのですが、これは、使いやすく負担なく使えて買って良かったです。

使い勝手や、物の品質には問題ありませんが。ボールグリップの差し込み部分にビットの刻印をしてあるため摩擦で消えてしまいそうです。到着時既に刺さっていたビットの文字は消えかけていました。挿入部に掛からない部分に塗装してくれてたらいいのに。

三角ねじを回すためのドライバーを探していましたが、ビットのみの安物よりもづらいばーでじっせきのあるかいしゃのものを選びました。しっかりとした軸先でした。通常のプラスマイナスの軸もよかったですが、こちらは軸径がもう少し細いと実際の修理作業でより使いやすいと思います。差し替え式では難しいですけど。

まだ実際に使用していませんが、しっかりした感じです。着磁脱磁簡単にできます。不思議ですね。